Evinrude Johnson Outboard Parts Warehouse

Evinrude / Johnson outboard tools

T.C.Electronics / Marine Johnson outboard Parts Warehouse
Electric starter motors
I need help page exploded internal parts drawings
Tech support application chart
I need help identifying my lower unit
Aluminum propellers
4 hp. thru 8 hp. 1980 and up
9.9 hp. & 15 hp, 1974 thru 2006
2 Cyl. 20-35 hp. Crossflow 3 cyl. 25-30-35 hp. Loopcharged
2 Cyl. crossflow 25-28 hp. thru-cavition exhaust 1978 thru 1997
2 Cyl. 40 - 50 hp. loop charged small gearcase 1989-2005
2 Cyl. 40 - 60 hp. 3 Cyl. 60 - 75 hp. loop charged small gearcase 1975-1988
2 Cyl. 40-60 hp. 1975 thru 2006+ 3 Cyl. 60 - 75 hp. loopcharged large gearcase 1975 thru 2001
V4 60 degree 1995 thru 2005 lower unit
V4 90 degree 1978 thru 1998 lower unit
V4 V6 Type "O" 1979 thru 2006 lower unit
V6 Type "O" heavy duty gears
V4-V6 type "M" drawings 2002 thru 2005
V6 Hydraulic shift lower unit 1976 thru 1978
Crankshaft seals
Bolts and screws
Oil seals lower gearcase
Cross reference chart 1980 + 1.2hp thru 15hp.
Cross reference chart 1980+ 20hp. to 28hp.
Cross reference chart 1980+ 30hp. to 60hp.
Cross reference chart 1980+ 70hp. to 175hp.
Cross reference chart 1980+ 185hp. to 300hp.
V6 outboard engine history
Seal kits
OMC Cobra Warehouse
Water Pumps
Anodes
Outboard Pistons
Lower unit gearcase components
Bearing housing
Gears / Gear sets
Long drive shaft
Drive shafts (lower unit)
Propeller shafts
Thrust washers
Thrust bearings
Leaf valves
Wrist pin bearing
Powerhead split sleeve bearing
Cage bearings
Roller bearings
Drive shaft bearing
Fuel Filters
Fuel pump kit
Powerhead gaskets
Head gasket
Tune up kit ( points )
Power trim relay
Starter solenoids
Rectifiers
Impellers
Ignition coils
Carburetor kits
Thermostats
Propeller nut kit
OMC stern drive part warehouse
Piston rings
Used parts and lower units
Power packs
Tools
V4 Outboard Drawing
Contact us
Bearing carrier lever
Pinion nut
Detente
Shims
Drain screw (magnetic)
Type "O" V4-V6 large gearcase identification
V-6 cross 90 power head gasket set
Oil pump to fill lower unit
Powerhead bearing chart

GLM marine aftermarket Evinrude / Johnson outboard tools

  • 9 Inch Aftermarket Johnson outboard propeller and bearing puller
  • Capacity 5 tons for use with all Evinrude Johnson outboard bearing carriers
  • Bearing race and seal driver used on all lower units
  • GLM # 90295 bearing puller installs-removes pinion bearing on Evinrude Johnson outboards that use bearings numbers 21610 and 21600. Refer to V4 - V6 outboard drawings for bearing applications that require the use of this tool
  • Pinion nut adaptor kit # 90340 design to hold 5/8" pinion nut when removing pinion gear and drive shaft. Use with V4 - V6 lower unit outboards (see drawings) and OMC / Mercruiser stern drive units

GLM Marine aftermarket Johnson outboard tools
90095 Johnson outboard bearing carrier puller.jpg
# 90095 Tool for johnson outboard motors, bearing carrier puller

# 90095 Propeller and bearing carrier puller $73.98

Johnson outboard motor tools
90295.jpg
# 90295 Puller kit for johnson outboard motors

# 90295 Lower unit drive shaft bearing puller $64.98

Johnson outboard motor tools
YF-6312-Bearing-race-and-seal-driver.jpg
YF-6312 Bearing race and seal driver

# YF-6312 Bearing race and seal driver $79.98

90061 Propeller  wrench.jpg
# 90061 Propeller wrench 1-1/16"

# 90061 Propeller wrench 1-1/16" $9.98

90340 2 pinion nut adaptor kit omc tools.jpg
90340 2 pinion nut adaptor kit omc tools

# 90340 Pinion nut adaptor kit $141.98

M Johnson lower unit oil pump.jpg
Johnson lower unit oil pump

# 401-11245-1 Johnson outboard lower unit oil pump $9.98

Print